Experimental and Theoretical Study on the Fatigue Crack Propagation in Stud Shear Connectors.

Steel-concrete composite girder bridges are subjected to reciprocal cyclic loading from vehicles, and the stud shear connectors are the key components for transmitting shear forces. Thus, it is necessary to study the fatigue performance of the stud shear connectors. At present, there are few studies on the fatigue crack propagation process of studs, and the variation curve of the crack depth of studs with the number of fatigue loading cycles is not clear. In this study, the degradation law of fatigue properties and the fatigue crack propagation law of stud shear connectors in steel-concrete composite structures are examined under fatigue loading. The fatigue properties, i.e., failure mode, the dynamic slip-fatigue number curve, cross-sectional characteristics, and the residual bearing capacity of the stud specimens, are first systematically studied through ten standard push-out specimen tests. The test results show that the relative value of the fatigue crack extension area increases, while the relative value of the residual bearing capacity of the studs decreases approximately linearly. Then, the expression of the relationship between the fatigue crack depth and the residual load-bearing capacity of the stud is proposed, based on the fatigue crack theory of fracture mechanics. Finally, combined with the ABAQUS and FRANC3D software, a fatigue crack propagation finite element analysis (FEA) model of the stud is established. The FEA results showed that the trends in the number of cyclic loads and the fatigue crack depth of studs are basically the same for the simulation curve, test curve and theoretical calculation curve.

Numerical Investigation of Interlaminar Stress of CRTS II Slab Ballastless Track Induced by Creep and Shrinkage of Concrete.

The secondary development of ABAQUS was carried out to calculate the shrinkage and creep of concrete, and a finite element model of the China Railway Track System (CRTS) II slab ballastless track was established. Then, the interlaminar stress of CRTS II slab ballastless track at different ages of the track slab during laying (AOTSL) caused by concrete shrinkage and creep was studied. The obtained results showed that the stress redistribution occurred in the sliding layer, which resulted in the generation of a gap. Although the gap length was slightly reduced due to the shear cogging, the sliding layer at the slab edge is more prone to produce gaps. Under the effect of shrinkage and creep of the ballastless track, large additional shear stress, up to 0.676 MPa, was induced at the interface between CA mortar and the track slab. Meanwhile, the appearance of additional vertical and lateral forces of the shear cogging was caused by the shrinkage and creep of the ballastless track. Additionally, by further analysis, the recommended AOTSL ranges from 120 days to 180 days.

Physical and Numerical Simulations on Mechanical Properties of a Prefabricated Underground Utility Tunnel.

The "U-shaped ferrule joint bars connections" have a stable mechanical property, requiring a low level of construction accuracy and a relatively simple connection process, which significantly increase the construction speed. Based on the "U-shaped ferrule joint bars connections" technology, a new type of prefabricated concrete underground utility tunnel was proposed. This prefabricated technology realizes a formwork-free construction and vertical support-free assembly of the top plate on site. Through the full-scale model static test and numerical analyses, the mechanical properties, i.e., the crack development law and bearing capacity, were systematically investigated to validate the effectiveness of the "U-shaped ferrule joint bars connections". The test results indicated that the performance of the "U-shaped ferrule joint bars connections" is reliable. During the loading process, the prefabricated utility tunnel experienced three stages, i.e., cracking, stiffness degradation, and ultimate failure. The numerical analysis results correlated with the test results well. The simulation results showed that the bearing capacities of the prefabricated underground utility tunnel and the cast-in-place utility tunnel were similar. The longitudinal joint connections of the prefabricated utility tunnel allow the structure as an integration to maintain favourable mechanical properties.

Numerical Investigation of Composite Behavior and Strength of Rectangular Concrete-Filled Cold-Formed Steel Tubular Stub Columns.

The objective of this study was to investigate the composite behavior of rectangular concrete-filled cold-formed steel (CFS) tubular stub columns under axial compression. A fine finite 3D solid element model of rectangular concrete-filled cold-formed steel tubular stub column was established by ABAQUS, which utilized a constitutive model of cold-formed steel considering the cold-forming effect and a triaxial plastic-damage constitutive model of the infilled concrete. Good agreement was achieved and the average discrepancy between the experimental and FE results was less than 5%. Based on the verified models, a further parametric analysis was carried out to reveal the influence of various factors on the strength and behavior of the concrete-filled rectangular cold-formed steel tubular stub columns. The factors included constitutive models adopted for cold-formed steel, length over width ratio of the rectangular section, wall-thickness and width, and concrete strength and yield strength of the cold-formed steel. A total of 144 FE models were analyzed. The stress nephogram was reasonably simplified in accordance with the limit state and a theoretical formula considering confinement coefficient was proposed to estimate the ultimate bearing capacity of concrete-filled rectangular cold-formed steel tubular stub columns using the superposition method. The calculated results showed satisfactory agreement with both the experimental and FE results, which proved the validity and accuracy of the formula proposed in this paper. In the proposed formula, the confinement coefficient of square concrete-filled cold-formed steel tubular stub columns is larger than that of hot-rolled steel counterparts but smaller than that of the stainless steel counterparts.